Dynamics/Kinematics/Angular Velocity

Introduction

edit

Content taken from Angular velocity and Rotating reference frame

In physics, angular velocity (  or  ), also known as angular frequency vector,[1] is a vector measure of rotation rate, that refers to how fast an object rotates or revolves relative to another point, i.e. how fast the angular position or orientation of an object changes with time.

There are two types of angular velocity: orbital angular velocity and spin angular velocity. Spin angular velocity refers to how fast a rigid body rotates with respect to its center of rotation. Orbital angular velocity refers to how fast a point object revolves about a fixed origin, i.e. the time rate of change of its angular position relative to the origin. Spin angular velocity is independent of the choice of origin, in contrast to orbital angular velocity which depends on the choice of origin.

In general, angular velocity is measured in angle per unit time, e.g. radians per second (angle replacing distance from linear velocity with time in common). The SI unit of angular velocity is expressed as radians per second with the radian having a dimensionless value of unity, thus the SI units of angular velocity are listed as 1/s or s−1. Angular velocity is usually represented by the symbol omega (ω, sometimes Ω). By convention, positive angular velocity indicates counter-clockwise rotation, while negative is clockwise.

For example, a geostationary satellite completes one orbit per day above the equator, or 360 degrees per 24 hours, and has angular velocity ω = (360°)/(24 h) = 15°/h, or (2π rad)/(24 h) ≈ 0.26 rad/h. If angle is measured in radians, the linear velocity is the radius times the angular velocity,  . With orbital radius 42,000 km from the earth's center, the satellite's speed through space is thus v = 42,000 km × 0.26/h ≈ 11,000 km/h. The angular velocity is positive since the satellite travels eastward with the Earth's rotation (counter-clockwise from above the north pole.)

Angular velocity is a pseudovector, with its magnitude measuring the angular speed, the rate at which an object rotates or revolves, and its direction pointing perpendicular to the instantaneous plane of rotation or angular displacement. The orientation of angular velocity is conventionally specified by the right-hand rule.[2]

Orbital angular velocity of a point particle

edit

Particle in two dimensions

edit
 
The angular velocity of the particle at P with respect to the origin O is determined by the perpendicular component of the velocity vector v.

In the simplest case of circular motion at radius  , with position given by the angular displacement   from the x-axis, the orbital angular velocity is the rate of change of angle with respect to time:  . If   is measured in radians, the arc-length from the positive x-axis around the circle to the particle is  , and the linear velocity is  , so that  .

In the general case of a particle moving in the plane, the orbital angular velocity is the rate at which the position vector relative to a chosen origin "sweeps out" angle. The diagram shows the position vector   from the origin   to a particle  , with its polar coordinates  . (All variables are functions of time  .) The particle has linear velocity splitting as  , with the radial component   parallel to the radius, and the cross-radial (or tangential) component   perpendicular to the radius. When there is no radial component, the particle moves around the origin in a circle; but when there is no cross-radial component, it moves in a straight line from the origin. Since radial motion leaves the angle unchanged, only the cross-radial component of linear velocity contributes to angular velocity.

The angular velocity ω is the rate of change of angular position with respect to time, which can be computed from the cross-radial velocity as:

 

Here the cross-radial speed   is the signed magnitude of  , positive for counter-clockwise motion, negative for clockwise. Taking polar coordinates for the linear velocity   gives magnitude   (linear speed) and angle   relative to the radius vector; in these terms,  , so that

 

These formulas may be derived from  ,   and  , together with the projection formula  , where  .

In two dimensions, angular velocity is a number with plus or minus sign indicating orientation, but not pointing in a direction. The sign is conventionally taken to be positive if the radius vector turns counter-clockwise, and negative if clockwise. Angular velocity then may be termed a pseudoscalar, a numerical quantity which changes sign under a parity inversion, such as inverting one axis or switching the two axes.

Particle in three dimensions

edit
 
The orbital angular velocity vector encodes the time rate of change of angular position, as well as the instantaneous plane of angular displacement. In this case (counter-clockwise circular motion) the vector points up.

In three-dimensional space, we again have the position vector r of a moving particle. Here, orbital angular velocity is a pseudovector whose magnitude is the rate at which r sweeps out angle, and whose direction is perpendicular to the instantaneous plane in which r sweeps out angle (i.e. the plane spanned by r and v). However, as there are two directions perpendicular to any plane, an additional condition is necessary to uniquely specify the direction of the angular velocity; conventionally, the right-hand rule is used.

Let the pseudovector   be the unit vector perpendicular to the plane spanned by r and v, so that the right-hand rule is satisfied (i.e. the instantaneous direction of angular displacement is counter-clockwise looking from the top of  ). Taking polar coordinates   in this plane, as in the two-dimensional case above, one may define the orbital angular velocity vector as:

 

where θ is the angle between r and v. In terms of the cross product, this is:

 

From the above equation, one can recover the tangential velocity as:

 

Note that the above expression for   is only valid if   is in the same plane as the motion.

Addition of angular velocity vectors

edit
 
Schematic construction for addition of angular velocity vectors for rotating frames

If a point rotates with orbital angular velocity   about its center of rotation in a coordinate frame   which itself rotates with a spin angular velocity   with respect to an external frame  , we can define   to be the composite orbital angular velocity vector of the point about its center of rotation with respect to  . This operation coincides with usual addition of vectors, and it gives angular velocity the algebraic structure of a true vector, rather than just a pseudo-vector.

The only non-obvious property of the above addition is commutativity. This can be proven from the fact that the velocity tensor W (see below) is skew-symmetric, so that   is a rotation matrix which can be expanded as  . The composition of rotations is not commutative, but   is commutative to first order, and therefore  .

Notice that this also defines the subtraction as the addition of a negative vector.

Angular velocity vector for rigid body or reference frame

edit

Given a rotating frame of three unit coordinate vectors, all the three must have the same angular speed at each instant. In such a frame, each vector may be considered as a moving particle with constant scalar radius.

The rotating frame appears in the context of rigid bodies, and special tools have been developed for it: the spin angular velocity may be described as a vector or equivalently as a tensor.

Consistent with the general definition, the spin angular velocity of a frame is defined as the orbital angular velocity of any of the three vectors (same for all) with respect to its own center of rotation. The addition of angular velocity vectors for frames is also defined by the usual vector addition (composition of linear movements), and can be useful to decompose the rotation as in a gimbal. All components of the vector can be calculated as derivatives of the parameters defining the moving frames (Euler angles or rotation matrices). As in the general case, addition is commutative:  .

By Euler's rotation theorem, any rotating frame possesses an instantaneous axis of rotation, which is the direction of the angular velocity vector, and the magnitude of the angular velocity is consistent with the two-dimensional case.

If we choose a reference point   fixed in the rigid body, the velocity   of any point in the body is given by

 

Angular velocity components from the basis vectors of a body-fixed frame

edit

Consider a rigid body rotating about a fixed point O. Construct a reference frame in the body consisting of an orthonormal set of vectors   fixed to the body and with their common origin at O. The angular velocity vector of both frame and body about O is then

 

Here

  is the time rate of change of the frame vector   due to the rotation.

Note that this formula is incompatible with the expression

 

as that formula defines only the angular velocity of a single point about O, while the formula in this section applies to a frame or rigid body. In the case of a rigid body a single   has to account for the motion of all particles in the body.

Components from Euler angles

edit
 
Diagram showing Euler frame in green

The components of the spin angular velocity pseudovector were first calculated by Leonhard Euler using his Euler angles and the use of an intermediate frame:

  • One axis of the reference frame (the precession axis)
  • The line of nodes of the moving frame with respect to the reference frame (nutation axis)
  • One axis of the moving frame (the intrinsic rotation axis)

Euler proved that the projections of the angular velocity pseudovector on each of these three axes is the derivative of its associated angle (which is equivalent to decomposing the instantaneous rotation into three instantaneous Euler rotations). Therefore:[3]

 

This basis is not orthonormal and it is difficult to use, but now the velocity vector can be changed to the fixed frame or to the moving frame with just a change of bases. For example, changing to the mobile frame:

 

where   are unit vectors for the frame fixed in the moving body. This example has been made using the Z-X-Z convention for Euler angles.

Angular velocity tensor or skew-symmetric matrix

edit

The angular velocity vector   defined above may be equivalently expressed as an angular velocity tensor, the matrix (or linear mapping) W = W(t) defined by:

 

This is an infinitesimal rotation matrix or a skew-symmetric matrix. The linear mapping W acts as  :

 

Calculation from the orientation matrix

edit

A vector   undergoing uniform circular motion around a fixed axis satisfies:

 

Angular velocity as a vector field

edit

Also, it can be shown that the spin angular velocity vector field is exactly half of the curl of the linear velocity vector field v(r) of the rigid body. In symbols,

 

Rigid body considerations

edit
 
Position of point P located in the rigid body (shown in blue). Ri is the position with respect to the lab frame, centered at O and ri is the position with respect to the rigid body frame, centered at O'. The origin of the rigid body frame is at vector position R from the lab frame.

The same equations for the angular speed can be obtained reasoning over a rotating rigid body. Here is not assumed that the rigid body rotates around the origin. Instead, it can be supposed rotating around an arbitrary point that is moving with a linear velocity V(t) in each instant.

To obtain the equations, it is convenient to imagine a rigid body attached to the frames and consider a coordinate system that is fixed with respect to the rigid body. Then we will study the coordinate transformations between this coordinate and the fixed "laboratory" system.

As shown in the figure on the right, the lab system's origin is at point O, the rigid body system origin is at O' and the vector from O to O' is R. A particle (i) in the rigid body is located at point P and the vector position of this particle is Ri in the lab frame, and at position ri in the body frame. It is seen that the position of the particle can be written:

 

The defining characteristic of a rigid body is that the distance between any two points in a rigid body is unchanging in time. This means that the length of the vector   is unchanging. By Euler's rotation theorem, we may replace the vector   with   where   is a 3×3 rotation matrix and   is the position of the particle at some fixed point in time, say t = 0. This replacement is useful, because now it is only the rotation matrix   that is changing in time and not the reference vector  , as the rigid body rotates about point O'. Also, since the three columns of the rotation matrix represent the three versors of a reference frame rotating together with the rigid body, any rotation about any axis becomes now visible, while the vector   would not rotate if the rotation axis were parallel to it, and hence it would only describe a rotation about an axis perpendicular to it (i.e., it would not see the component of the angular velocity pseudovector parallel to it, and would only allow the computation of the component perpendicular to it). The position of the particle is now written as:

 

Taking the time derivative yields the velocity of the particle:

 

where Vi is the velocity of the particle (in the lab frame) and V is the velocity of O' (the origin of the rigid body frame). Since   is a rotation matrix its inverse is its transpose. So we substitute  :

 
 
 

or

 

where   is the previous angular velocity tensor.

It can be proved that this is a skew symmetric matrix, so we can take its dual to get a 3 dimensional pseudovector that is precisely the previous angular velocity vector  :

 

Substituting ω for W into the above velocity expression, and replacing matrix multiplication by an equivalent cross product:

 

It can be seen that the velocity of a point in a rigid body can be divided into two terms – the velocity of a reference point fixed in the rigid body plus the cross product term involving the orbital angular velocity of the particle with respect to the reference point. This angular velocity is what physicists call the "spin angular velocity" of the rigid body, as opposed to the orbital angular velocity of the reference point O' about the origin O.

Consistency

edit

We have supposed that the rigid body rotates around an arbitrary point. We should prove that the spin angular velocity previously defined is independent of the choice of origin, which means that the spin angular velocity is an intrinsic property of the spinning rigid body. (Note the marked contrast of this with the orbital angular velocity of a point particle, which certainly does depend on the choice of origin.)

 
Proving the independence of spin angular velocity from choice of origin

See the graph to the right: The origin of lab frame is O, while O1 and O2 are two fixed points on the rigid body, whose velocity is   and   respectively. Suppose the angular velocity with respect to O1 and O2 is   and   respectively. Since point P and O2 have only one velocity,

 
 

The above two yields that

 

Since the point P (and thus  ) is arbitrary, it follows that

 

If the reference point is the instantaneous axis of rotation the expression of the velocity of a point in the rigid body will have just the angular velocity term. This is because the velocity of the instantaneous axis of rotation is zero. An example of the instantaneous axis of rotation is the hinge of a door. Another example is the point of contact of a purely rolling spherical (or, more generally, convex) rigid body.

Time derivatives in two frames

edit

Content taken from Rotating reference frame

Introduce the unit vectors   representing standard unit basis vectors in the rotating frame. As they rotate they will remain normalized. If we let them rotate at the speed of   about an axis   then each unit vector   of the rotating coordinate system abides by the following equation:

 

Then if we have a vector function  ,

 

and we want to examine its first derivative we have (using the product rule of differentiation):[4][5]

 

where   is the rate of change of   as observed in the rotating coordinate system. As a shorthand the differentiation is expressed as:

 

This result is also known as the Transport Theorem in analytical dynamics and is also sometimes referred to as the Basic Kinematic Equation.[6]


References

edit
  1. Cummings, Karen; Halliday, David (2007). Understanding physics. New Delhi: John Wiley & Sons Inc., authorized reprint to Wiley – India. pp. 449, 484, 485, 487. ISBN 978-81-265-0882-2. https://books.google.com/books?id=rAfF_X9cE0EC. (UP1)
  2. Hibbeler, Russell C. (2009). Engineering Mechanics. Upper Saddle River, New Jersey: Pearson Prentice Hall. pp. 314, 153. ISBN 978-0-13-607791-6. https://books.google.com/books?id=tOFRjXB-XvMC&q=angular+velocity&pg=PA314. (EM1)
  3. K.S.HEDRIH: Leonhard Euler (1707–1783) and rigid body dynamics
  4. Cornelius Lanczos (1986). The Variational Principles of Mechanics (Reprint of Fourth Edition of 1970 ed.). Dover Publications. pp. Chapter 4, §5. ISBN 0-486-65067-7. https://books.google.com/books?num=10&btnG=Google+Search. 
  5. John R Taylor (2005). Classical Mechanics. University Science Books. p. 342. ISBN 1-891389-22-X. https://books.google.com/books?id=P1kCtNr-pJsC&pg=PP1. 
  6. Corless, Martin. "Kinematics" (PDF). Aeromechanics I Course Notes. Purdue University. p. 213. Archived from the original (PDF) on 24 October 2012. Retrieved 18 July 2011.