University of Florida/Egm3520/s13.team5.r2

--Siefman (discusscontribs) 20:33, 6 February 2013 (UTC)

Problem 2.1 (Pb-9.1 in sec.9.)

edit

On our honor, we did this problem on our own, without looking at the solutions in previous semesters or other online solutions.

Problem Statement

edit

Part 1

edit

Using Example 2.04(p.9-1), solve for the reaction forces   and   as if the stress-strain relation is modeled by

 

(2.1-1)

Part 2

edit

Do the results depend on the length or the Young's modulus of each segment?

Given

edit

 

(2.1-2)

 

(2.1-3)

 

(2.1-4)

 

(2.1-5)

 

(2.1-6)

 

(2.1-7)

Solution

edit

Part 1

edit
Step 1: Draw the free-Body diagram
edit

Begin by removing the supports and drawing the free-body diagram for the entire bar AB and the four sections as shown below.

 
Figure 2.1-1. Free-body diagrams of all the sections of bar AB


Step 2: Determine the internal forces
edit

Using   the internal force,  , can be determined in each segment.

 

(2.1-8)

 

(2.1-9)

 

(2.1-10)

 

(2.1-11)

Step 3: Calculate the displacement
edit

Rearranging Equation 2.1-1,

 

(2.1-12)

 

(2.1-13)


The displacement for the whole bar can be represented as a sum of the displacements of each segment and set equal to 0 since both ends of the bar are fixed,

 

(2.1-14)

 

(2.1-15)

 

(2.1-16)

 

(2.1-17)

 

(2.1-18)


Substituting the expressions for   from above and adding the components together, we receive

 

(2.1-19)


Step 4: Solve for the reaction at B
edit

  can be cancelled out and like-terms can be grouped to give us

 

(2.1-20)

 

(2.1-21)


Since  , Equation 2.1-21 can be rewritten as

 

(2.1-22)

 
 

(2.40-13)

Step 5: Solve for the reaction at A
edit

Referring back the free-body diagram of the entire bar,

 

(2.1-23)

 

(2.1-24)

 
 

(2.1-25)

Part 2

edit

Referring to Equation 2.1-19,   can be divided out of both terms and set equal to zero. This confirms that the results do not depend on the length of each segment nor Young's modulus, so long as these values are the same in every segment of the bar.

Problem 2.2 (P2.12, Beer 2012)

edit

On our honor, we did this problem on our own, without looking at the solutions in previous semesters or other online solutions.

Problem Statement

edit

A thread stretching from B to C is subjected to a tension of 10 N. The maximum allowable normal stress is 10 MPa and  = 200GPa. The length of the thread may not increase by more than 1%. What is the required diameter of the thread?


 
Figure 2.2-1 String under axial load of 10 N

Solution

edit

Step One: Determine a relationship between diameter and normal stress and diameter and elongation

edit

The normal stress in the string,  , is given by Equation 2.2-1, where   is the applied load and   is the area.

 

(2.2-1)

The elongation of the string is given by Equation 2.2-2, where   is the elongation of the string,   is the length of the string and   is the Young's modulus given in the problem statement.

 

(2.2-2)

The diameter,  , can later be inserted into Equation 2.2-1 by equating it to the area, as shown in Equation 2.2-3

 

(2.2-3)

Step Two: Calculate the diameter if the maximum normal stress is limiting

edit

Inserting Equation 2.2-3 in to 2.2-1 and solving for   gives

 

(2.2-4)

Plugging in the given values from the problem statement,


 

(2.2-5)

Step Three: Calculate the diameter if the elongation is limiting

edit

First it was assumed that the string had a length   of 1 meter, meaning that a 1% elongation would be 0.01 meters. The proportionality of these values is what is important, because their units will cancel later.

Inserting Equation 2.2-3 in to 2.2-2 and solving for d gives

 

(2.2-6)


Plugging in the given values from the problem statement and the assumed values,

 

(2.2-7)

Step Four: Choose the smallest diameter

edit

The smallest allowable diameter, and the minimum that is required, occurred when the one-percent elongation was the limiting factor.

 
 

Problem 2.3 ( P2.16, Beer 2012)

edit

On our honor, we did this problem on our own, without looking at the solutions in previous semesters or other online solutions.

Problem Statement

edit

A brass tube AB connected at point A, is being applied a load P on top of the tube. At the bottom of the structure is a rigid plate C attached at point B. An aluminum cylinder is hung downwards from point D, and attached to the rigid plate at point C. With the given values, what is the force load,  , that is being applied to the brass tube?


 
Figure 2.3-1. System in problem statement

Given:


  ,  


  ,  


  ,  

Solution

edit

Step One:Determine the deflection on the brass tube

edit

First step is to analyze the brass tube at point A and B.

At the segment AB, the brass tube experiences a state of compression when the load   is applied at point A.

 

 

(2.3-1)

In order to find the load applied to the brass tube, a relation between the cylinder and the tube has to be made through the equations of deflection. For the brass tube the deflection is:

 

(2.3-2)

After substituting the given values from the problem statement:

 

(2.3-3)

 

(2.3-4)

Step Two:Determine the deflection on the aluminum cylinder

edit

Next, is to find the deflection that is created by the load at point A, on the aluminum cylinder collected at point D. The deflection of the aluminum cylinder hanging at point D.
The deflection of the aluminum cylinder is measured by the following equation:

 


(2.3-5)

After substituting the values given in the above problem statement, the equations looks like the following:


 


(2.3-6)

 

(2.3-7)

Step 3 (Finding the stress load)

edit

Total deflection is as followed:

 


(2.3-8)

 


(2.3-9)


 
 

Problem 2.4 ( P2.24, Beer 2012)

edit

On our honor, we did this problem on our own, without looking at the solutions in previous semesters or other online solutions.

Problem Statement

edit

Determine the deformations of members BD and DE in the steel truss (  = 29 E6 psi) shown in Figue 2.4-1. Their cross-sectional areas of BD and DE are 2 in^2 and 3 in^2 respectively. The steel truss is shown in Figure 2.4-1

 
Figure 2.4-1. Diagram of the truss

Given:

 
 
 
 

Solution

edit

Step One:Draw a free-body diagram of the system

edit

The free-body diagram is shown in Figure 2.4-2.

 
Figure 2.4-2. Free-body diagram of the tress


Step Two: Use the equilibrium of moments and forces at point F

edit

The sum of moments around point F is zero and the counterclockwise direction is taken as positive.

 

(2.4-1)

Solving for   gives,

 

The sum of forces in the y-direction is also zero.

 

(2.4-2)

Therefore,   is

 

The sum of forces in the x-direction is also zero.

 

(2.4-3)

Therefore,   is

 

Step Three: Isolate the truss at FDG and solve for the forces

edit

First, a free-body diagram must be made for the isolated truss FDG.

 
Figure 2.4-3. FBD for isolated truss

To solve for  , take the sum of the forces in the x-direction, which is zero.


 

(2.4-4)

Knowing   from Step Two,   is

 

Next, the sum of the moments about G is take, which also equals zero.

 

(2.4-5)

Therefore,   is

 

Step Four: Solve for the deformation of members BD and DE

edit

The deformation of members BD and DE are given by Equations 2.4-6 and 2.4-7, respectively.

 

(2.4-6)

 

(2.4-7)

Solving for   and   with the given and calculated values gives


 
 


 
 

Problem 2.5 ( P2.40, Beer 2012)

edit

On our honor, we did this problem on our own, without looking at the solutions in previous semesters or other online solutions.

Problem Statement

edit


A Polystyrene rod consisting of two cylindrical portion AB and BC is restrained at both ends ans supports two 6-kips loads as shown. Knowing that  , determine the reactions at A and C, and the normal stress in each portion of the rod.

 
Problem 2.40

Solution

edit

Step One:Find the reactions at A and C

edit
 
FBD of Problem 2.40


The elongation of the rod is zero.


 

(2.40-1)


The forces are equal in opposite directions.


 

(2.40-2)


 

(2.40-3)

By substitution and simplifying the elongation of the rod can be rearranged to solve for   in terms of  

 

(2.40-4)


 

(2.40-5)

 

(2.40-6)


From the free body diagram the sum of

  totals to 12 kips.

 

(2.40-7)


After substitution and simplifying the reactions can be calculated.


 

(2.40-8)

 

(2.40-9)

 
 

(2.40-10)

 
 

(2.40-11)

Step Two:Calculate the normal stress for both members

edit


The normal stress for the member equals the stress divided by the area of the members. After substitution these normal stresses can be calculated.

 

(2.40-12)


 
 

(2.40-13)

 

(2.40-14)

 
 

(2.40-15)

Problem 2.6 ( P2.44, Beer 2012)

edit

On our honor, we did this problem on our own, without looking at the solutions in previous semesters or other online solutions.

Problem Statement

edit

The rigid bar AD is supported by two steel wires of   in. diameter   psi) and a pin and bracket at D. Knowing that the wires were initially taut, determine (a) the additional tension in each wire when a 120-lb load P is applied at B, (b) the corresponding deflection of point B.

Solution

edit

Step One:Draw the free-body diagram

edit
 
FBD of Problem 2.44

Let   be the rotation of the bar ABCD.


 

(2.44-1)


 

(2.44-2)

 

(2.44-3)

 

(2.44-4)


 

(2.44-5)


 

(2.44-6)


 

(2.44-7)

 

(2.44-8)

Using the free body diagram ABCD the sum of the momentum is equal to 0.

 

(2.44-9)

 

(2.44-10)

 

(2.44-11)


Substituting into these equation give the tensions in each wire.

 
 

(2.44-12)

 
 

(2.44-13)

The deflection of the beam is the angle of the moment   multiplied by the length of the beam (16in).

 
 

(2.44-14)

Contributors

edit

Team Designee: Daniel Siefman

Table of Assignments
Problem Number

Solved by

Reviewed by

2.1

Tim Shankwitz and Gregory Grannell

All

2.2

María José Carrasquilla and Daniel Siefman

All

2.3

Michael Lindsay and Joshua Herrera

All

2.4

Michael Lindsay and Daniel Siefman

All

2.5

Andrew Moffatt and Phil D Mauro

All

2.6

Andrew Moffatt and Phil D Mauro

All

References

edit
Beer, F. P., Johnston, E. R., Jr., DeWolf, J. T., & Mazurek, D. F. (2012). Mechanics of materials (6th ed.). New York, NY: McGraw Hill.